Construction Skills
Location:
Program Status:
Program Code:
Co-ordinator:
Credential:
Classes Start:
Tuition/ Fees:
Peterborough
Accepting applications
CNS
Ontario College Certificate
September 21, 2009
$1,606.00 per semester *
* Tuition and fees subject to change.
- Program Information
- Program Curriculum
- Course Descriptions
Program Highlights
This compressed, two-semester program will prepare you for employment in the construction sector. You will be trained in hand and power tool usage, carpentry/framing techniques, blueprint reading, electricity basics, welding, masonry basics, safety, WHMIS, and applied construction mathematics. Completion of this certificate will also prepare you to pursue an apprenticeship in a variety of construction-related trades. As well, you may qualify for exemption from the Basic Level General Carpenter Apprentice or Basic Brick and Stone Mason in-school programs. The program is designed to alleviate the shortage of skilled trade workers in the construction industry. Semester one of the Construction Skills program runs from September 22 to December 12. Semester two starts January 12, 2009 and ends April 3, 2009.
What it Takes to Succeed
To be employed in construction you need to:
- be able to follow instructions carefully and work independently
- maintain safety at the site
- be able to multi-task
- adhere to industry-approved standards and relevant codes
- understand the basic processes and phases of construction projects
- complete projects according to blueprint specifications.
In addition, the ability to practice professional conduct on-site, and communicate and work effectively in a team environment will be key to your success. You will have the opportunity to practice and demonstrate these skills throughout the program. You must also be ready and able to work in a construction environment in all kinds of conditions.
Career Opportunities
Graduates will be prepared for work on residential, industrial and commercial construction sites, performing entry level tasks on projects such as:
- residential framing
- renovation carpentry
- maintenance carpentry
- finish carpentry
- roofing
- insulation installation
- exterior siding installation.
Minimum Admission Requirements
OSSD with any combination of (E), (C) or (U) courses or equivalent.
Mature Students
If you are 19 years of age or older before classes start, and you do not possess an OSSD, you can write the Canadian Adult Achievement Test to assess your eligibility for admission.
Selection Process
Related Programs
You may also be interested in the Electrical Techniques or the Welding Techniques program.
| Course | Hours |
| Semester 1 | |
| Human Relations | 45.00 |
| Basic Electrical Wiring I | 24.00 |
| Carpentry I | 76.00 |
| Health and Safety | 36.00 |
| Masonry I | 80.00 |
| Plumbing Supply Systems I | 24.00 |
| Print Reading I | 24.00 |
| Trade Calculations and Layout | 48.00 |
| Semester 2 | |
| Professional Portfolio Development | 36.00 |
| Basic Electrical Wiring II | 24.00 |
| Carpentry II | 76.00 |
| Computer Applications | 24.00 |
| Interior Finishing | 40.00 |
| Masonry II | 88.00 |
| Plumbing Supply & DWV Systems II | 24.00 |
| Print Reading II | 24.00 |
| Welding I | 24.00 |
Semester 1
Human Relations
Course Number: MGMT005
This course examines self-awareness, interpersonal relations, motivation, stress, small group dynamics, and organizational behaviour. Particular attention will be paid to leadership and conflict management in employment situations. Contemporary developments reshaping human relations will be introduced for study and discussion.
Units: 45.00
Hours: 45.00
Basic Electrical Wiring I
Course Number: ELCT065
This course has been prepared for potential apprentices entering the construction trade. The material is designed to review fundamental concepts which include: safety, energizing the home, basic circuits, and house wiring diagrams and prints.
Units: 24.00
Hours: 24.00
Carpentry I
Course Number: CRPT002
This course covers the common types of wood, wood structures, wood joints, and hardware used in today's construction. The selection, safe use, and maintenance of hand tools, portable power tools, and stationary power tools required on a typical construction site will also be covered.
Units: 76.00
Hours: 76.00
Health and Safety
Course Number: CNST089
This course has been prepared for potential apprentices entering the construction trade. This course is designed to develop in the learner knowledge of the health hazards and safety risks that are present on the job site and to equip them with the tools required for personal protection and general safety. Upon completion of this course, the learner will have earned several required certificates for construction site employment.
Units: 36.00
Hours: 36.00
Masonry I
Course Number: CNST087
This course has been prepared for potential apprentices entering the construction trade. This covers the selection, safe use, and maintenance of hand tools and portable power tools and equipment required on a typical construction site. Also covered will be footings and foundations for structurally sound masonry. Also covered will be the health hazards and safety risks related to this trade.
Units: 80.00
Hours: 80.00
Plumbing Supply Systems I
Course Number: MECH165
This course is an introduction to basic plumbing terminology, maintenance, safety procedures and tool requirements. Plumbing fixtures, water supply systems, and valve types will also be covered.
Units: 24.00
Hours: 24.00
Print Reading I
Course Number: CNST085
This course covers the basic concepts of orthographic and pictorial drawings and sketches and drafting terminology. Interpretation of information found on architectural drawings such as, lot plans, floor plans and elevations will also be covered in this course.
Units: 24.00
Hours: 24.00
Trade Calculations and Layout
Course Number: MATH079
This course covers the basic mathematical principles and geometry skills as required by the learner entering a trade. Topics covered will include fractions, decimals, and the S.I. and imperial systems of measurement, including conversions between systems. Mensuration, ratio and proportion, Pythagorean Theorem, Ohm's Law and trade related problems will also be covered. The basic principles of geometry will include line-work, angles and triangles, quadrilaterals, circles, polygons, the ellipse, ratio and proportion and arches.
Units: 48.00
Hours: 48.00
Semester 2
Professional Portfolio Development
Course Number: BUSN078
This course will assist students to locate and win positions they want in the workplace. The use and development of a professional portfolio will be emphasized. Through career analysis self-assessment, goal setting, and portfolio development participants will improve their ability to link their skills and knowledge to appropriate career positions. The basics of job searching will be enhanced with sessions on electronic resume posting, web site searches, and online job links. Participants will complete this course with the foundation of a professional portfolio and the knowledge to find the work they want.
Units: 36.00
Hours: 36.00
Basic Electrical Wiring II
Course Number: ELCT066
This course has been prepared for potential apprentices entering the construction trade. This course will familiarize the learner with permit procedures, room layouts, electrical code standards and most of all: safety.Pre-requisite:Basic Electrical Wiring I (ELCT065)
Units: 24.00
Hours: 24.00
Carpentry II
Course Number: CRPT003
Pre-requisites
This course has been prepared for potential apprentices entering the construction trade. This course covers properties of wood and lumber and methods of wall framing. Learners will also be introduced to relevant sections of building codes as applicable.
Units: 76.00
Hours: 76.00
Computer Applications
Course Number: COMP287
This course has been prepared for potential apprentices entering the construction trade. This course covers the use of word processing to generate professional reports and quotations. Creating spreadsheets using MS Excel for business applications will also be examined.
Units: 24.00
Hours: 24.00
Interior Finishing
Course Number: CRPT004
This course has been prepared for potential apprentices entering the construction trade. This course covers the composition of exterior and interior walls. Included are the application and installation of exterior sheathing, insulation, vapour barriers, drywall, taping, priming and painting and trim work.
Units: 40.00
Hours: 40.00
Masonry II
Course Number: CNST088
Pre-requisites
This course has been prepared for potential apprentices entering the construction trade. This course covers cleaning systems and chemicals, bonding techniques, bonding materials, and common and historic masonry bonds.
Units: 88.00
Hours: 88.00
Plumbing Supply & DWV Systems II
Course Number: MECH166
Pre-requisites
This course is an introduction to basic plumbing terminology, symbol and component identification and layout of drain, waste and vent systems.
Units: 24.00
Hours: 24.00
Print Reading II
Course Number: CNST086
Pre-requisites
This course has been prepared for potential apprentices entering the construction trade. This course deals with interpretation of imperial and metric residential drawings. Use will also be made of the National and Ontario Building Codes to ensure that construction drawings are in compliance. Also included, will be a preliminary look at barrier free access.
Units: 24.00
Hours: 24.00
Welding I
Course Number: MECH167
This course covers both Oxy-Fuel (OFW) and Arc Welding (SMAW) as may be used on a construction site. It also covers set up, safe use and operating principles of the related equipment. Fusion welding on light and heavy steel in the flat and horizontal positions, brazing and manual flame cutting will also be covered.
Units: 24.00
Hours: 24.00